Hardwood Victoria

Can engineered hardwood be refinished? It depends on the wear layer

Your engineered floor is looking worn, and you'd like to know whether it can be sanded back like solid hardwood. That works when the layer of real wood on top is thick enough, and not otherwise. The National Wood Flooring Association puts the line at about 2.5 mm. In general, the wear layer of any wood floor "that is being considered for a refinish should not be less than 3/32” (approximately 2.5mm)" (Hardwood Floors Magazine, NWFA). Some engineered floors clear that easily and can take several sandings. Others "may only have a paper-thin veneer of real wood that has been peeled from the log" (same article), and a sander would go straight through it.

What you really need to find out is how much real wood is left on top, and whether anything about the floor makes it hard to sand evenly.

What makes engineered hardwood different from solid?

Solid wood flooring is "a solid piece of wood from top to bottom." Engineered wood flooring is "normally made using multiple wood veneers or slats of wood glued together at opposing directions" (NWFA Engineered Wood Flooring Refinishable Program). The visible top is the wear layer, also known as the lamella. Underneath it, the core can be "layers of wood veneers, solid lumber fillets, or some type of composite material," and "no matter what the overall construction of the engineered product is, the thickness of the topmost layer determines whether the floor can be refinished" (Hardwood Floors Magazine, NWFA).

That top layer is the only part a sander can use. Sand past it and you reach the core, and the article spells out what happens then: after "sanding through the veneer," the best option may be to "get creative with paints, dyes, and graining tools," and when that is not feasible "it often leads to floor replacement" (Hardwood Floors Magazine, NWFA).

If your house is an older character home with solid fir or oak, start with the guide to fir and oak floors in Victoria instead.

How thick does the wear layer need to be?

Wear layers vary widely. The thin end is the peeled veneer, and the thick end is "a sawn wear layer that can be up to ¼” (6.35mm) thick (comparable to the wear layer on most ¾” solid wood floors)" (Hardwood Floors Magazine, NWFA).

The NWFA's certification for refinishable engineered flooring draws a similar line. Factory-finished products "shall have a minimum wear layer thickness of 2.5mm," unfinished products 3.2mm, and textured products 2.5mm "at the lowest point" (NWFA Refinishable Program).

For a floor above that line, it's worth looking up the manufacturer's own rating. Kährs says that, depending on wear-layer thickness, its engineered floors "can be sanded up to four times" (Kährs flooring FAQ). One of its 2.6 mm wear-layer oak products is listed as "Resandable 2-3 times" (Kährs Oak Sand product facts).

A normal sanding "should remove a minimal amount of wood, often less than 1/32”," but the number of sandings still "depends on the skill of the person sanding the floor, the type of equipment being used, the thickness of the remaining wear layer, and the flatness of the installed floor" (Hardwood Floors Magazine, NWFA). If your floor has been sanded before, it has less left than it had new.

How do you check the wear layer on your floor?

The wear layer shows on the side of a board, so look where an edge is exposed: "floor registers or by removing transition moldings," quarter round or base shoe, an edge where carpet meets the floor, or "leftover flooring in the basement, attic, garage, or storage rooms" (Hardwood Floors Magazine, NWFA).

A feeler gauge in a board gap works on solid floors, but it can mislead on some engineered ones because "the wear layer on some engineered wood flooring may not be as deep as the tongue" (same article). As a last resort, and with the owner's permission, a small hole can be drilled in a hidden spot and then patched with a "dowel or wood plug".

What else can stop an engineered floor from being sanded?

Even with a thick enough wear layer, a floor can't always be sanded.

Bevelled edges. To sand out a bevelled edge, "you will need to measure from the lowest point of the bevel profile," and sanding changes "the profile of the bevel and the look of the floor" (Hardwood Floors Magazine, NWFA). An NWFA technical advisor adds that "sometimes 3/32” is not enough if the beveled edges are so deep that sand through may occur by the time the bevels are sanded out" (Hardwood Floors Magazine, Tech Talk).

Texture. Hand-scraped, wire-brushed and sculpted floors "are extremely difficult and often cannot be sanded," because the low spots may be under the minimum thickness (Hardwood Floors Magazine, NWFA).

Flatness. "If the floor is out of flat it could lead to uneven sanding and possible sand through" (Tech Talk).

Some engineered products are not designed to be sanded at all. Mirage, for example, says its "Lock technology floors cannot be sanded. However, they can be recoated" (Mirage FAQ).

What if the wear layer is too thin to sand?

A thin-veneer floor can still be recoated, which renews the finish without sanding the wood. The Hardwood Floors Magazine article also says that "unless the floor has visible dents, wear patterns, or permanent cupping, or the customer wants to change the color of the floor, a maintenance recoat may suffice" (Hardwood Floors Magazine, NWFA). Bona's recoat system abrades the old finish and adds a fresh coat, and "if recoating a factory prefinished floor," only finishes from its Traffic HD line should be used (Bona Recoat Treatment). The hardwood floor recoating guide covers what makes a recoat hold, and the recoat page has the service details.

A recoat adds finish and removes nothing, so it won't take out nicks or dents that go into the wood. On a floor that can't be sanded, isolated damage is a repair question, and that work comes before any new finish goes on.

If you can't tell yet whether your floor needs a recoat, a sand-back or a repair, the form has a "Not sure yet" option for that.

What does refinishing engineered hardwood cost?

Published US cost guides list engineered hardwood separately. Bob Vila puts refinishing engineered floors at "around $3 to $5" per square foot, materials and labour (Bob Vila, updated May 2024). This Old House lists the same $3–$5 band for engineered wood (This Old House). For a floor that can only be recoated, the same Bob Vila guide says "recoating costs between $1 and $2 per square foot."

These are US figures in US dollars, so treat them as a sanity check on a quote rather than a local price. The refinishing hardwood floors guide covers cost and timeline for a full sand-back.

What should happen before anyone sands?

Moisture comes first. The NWFA's refinishable certification assumes owners "maintain temperature and humidity levels year-round" (NWFA Refinishable Program). Health Canada's guidance for homes is to keep relative humidity "between 30% and 50%" (Health Canada). If boards have cupped, the moisture source has to be dealt with before any sanding, for the reasons set out in the fir and oak guide.

The finish needs care too. One flooring professional quoted by the magazine warns that with water-based finish on a freshly sanded engineered floor, coats should not go on too heavy, "as the edges of the veneer can sometimes curl if exposed to too much moisture" (Tech Talk).

Wood dust "is considered carcinogenic to humans (Group 1)" according to the International Agency for Research on Cancer (CCOHS), which is a good reason to stay out of the rooms while the sanding is going on.

Frequently asked questions

Can I tell from the top whether my floor is engineered? You can't tell reliably. Even for professionals "it's sometimes hard to tell whether the floor is solid, engineered, or just a fancy picture of wood glued to plastic" (Hardwood Floors Magazine, NWFA). Check a board edge at a register or transition instead.

Describe your floor in the quote form

If you've measured the wear layer or found the product name on a leftover box, add it to the notes. The quote form asks what you think you need (recoat, full refinish, repair or water damage, or "Not sure yet") and where the floors are, and the notes box has room for a rough room count or square footage, floor age and any damage. Submitting does not commit you to anything.